wind turbine inspectiondrone inspection aiblade defectstaiwan offshore wind

Blade inspection AI in Taiwan: what the model gets wrong台灣風機葉片檢測 AI:模型會出錯的地方台湾のブレード点検AI:モデルが見誤るポイント

Drone circling an offshore turbine blade while wind turbine drone inspection AI flags defects on screen
Quick answer: Wind turbine drone inspection AI scans the several hundred photos a drone takes per turbine and flags likely defects such as leading edge erosion, trailing edge cracks and lightning damage. It finds candidates fast; severity grading on a 1 to 5 scale still needs a trained inspector checking location, size and growth.

Blade inspection AI in Taiwan: what the model gets wrong

Wind turbine drone inspection AI is very good at finding every mark on a blade. It's poor at deciding which of those marks will cost you a blade, and that second call is what an asset owner pays for.

I've inspected about 3,000 wind turbines, onshore and offshore, in Taiwan and the Philippines. My position after all those blades: let the model find, let a trained inspector grade, and make the report show which one made each call.

What does AI actually do in a drone blade inspection?

It sorts images. One drone flight around a turbine produces several hundred high-resolution photos covering 4 faces of each blade, and the AI turns that pile into a shortlist of suspected defects.

The 4 faces are the leading edge, trailing edge, pressure side and suction side. With 3 blades, that's 12 passes per turbine. Before AI, a reviewer scrolled every frame by hand. Now the model draws boxes around anomalies, suggests a defect class, and attaches a confidence score.

That saves real hours. The trouble is what lands on the shortlist.

Models trained on generic datasets flag bird droppings, grease streaks from the hub, rain beads, tower shadow and insect build-up on the leading edge. Offshore in the Taiwan Strait, salt haze on the lens adds its own false positives. Each false flag costs a human a few seconds. Across a full wind farm, those seconds become days.

The opposite error is worse. A thin crack with low contrast gets scored as a stain, falls below the confidence threshold, and never reaches a human.

Inspector reviewing AI flagged trailing edge crack on a blade image beside a severity grading sheet

Which blade defects matter most in Taiwan and Japan?

Leading edge erosion, trailing edge cracks, lightning damage and failing leading edge protection. Climate decides which one tops the list.

In Taiwan, the drivers are monsoon rain, typhoons and salt. Large offshore rotors run tip speeds near 90 m/s, so every raindrop hits the leading edge like grit. Erosion starts as pitting in the coating and works down to the laminate.

Japan adds a different stress. Winter lightning along the Sea of Japan coast is well documented as unusually energetic, and that coast includes Akita, one of the first offshore wind regions in Japan's push toward its 30 to 45 GW offshore target for 2040. Lightning damage near the tip and around the receptors deserves extra attention there.

Here's how AI performs on each class, based on what I see when reviewing model output against my own grading:

Defect classWhat AI does wellWhere AI strugglesWhat the inspector checks
Leading edge erosionFinds pitting and coating loss reliablyCan't judge depth from one imageWhether laminate or fibres are exposed
Trailing edge cracksFinds long, open splitsHairline cracks read as dirt or bond linesLength, orientation, both sides of the edge
Lightning damageFinds burn marks at receptorsSoot vs scorching, hidden delamination near the tipReceptor condition, tip bulging, follow-up need
Leading edge protection debondingFinds lifted tape or shell edgesEarly lift that casts no shadowEdge of the protection zone, peel direction
Surface contaminationFinds it every timeLabels it as damageRemoves it from the defect list
Add-ons (vortex generators, serrations)Counts missing piecesCracked bases still in placeCount against the blade drawing

The pattern is consistent. AI does well when a defect has strong contrast and a clear shape. It struggles when the answer depends on depth, context or the other side of the blade.

How do you grade blade defect severity, and why can't the model do it alone?

Most reports use a 1 to 5 severity scale, from cosmetic to stop the turbine. Grading needs location, size and history, and a single photo carries only part of that.

Scales differ between turbine makers and owners, but a common shape looks like this:

  1. Cosmetic. Log it, no action.
  2. Minor. Monitor at the next inspection.
  3. Moderate. Repair in the next planned maintenance window.
  4. Serious. Repair soon, consider reducing operation.
  5. Critical. Stop the turbine.

Take one 10 cm crack. Near the root, along the chord, it can be a structural concern. Near the tip, along the span, in the coating only, it might be a 2. The model sees the same pixels in both cases.

The position along the blade, measured in metres from the root, changes the grade. So does orientation. So does whether the crack crosses the trailing edge bond line.

Then there's history. Growth is the strongest signal in blade inspection. A 2 that doubled in length since last year is no longer a 2. Unless the AI pipeline has last year's images matched to the same blade, face and radius, it can't see growth at all.

How often should wind turbine blades be inspected by drone?

Once a year for a baseline, plus targeted flights after any event that could change a blade's condition overnight.

TriggerWhy it mattersTypical scope
Annual baselineBuilds the history that makes growth visibleAll blades, all 4 faces
After a typhoonSudden cracks, debonding, add-on lossTargeted first, then full
After a lightning alarmReceptor burns, tip damageThe struck turbine
Before end of warrantyEvidence for claimsFull, high resolution, documented
After a repairConfirms the fix heldThe repaired zone

In Taiwan, I'd plan the annual round outside typhoon season and keep crews ready for post-storm flights. In Japan, owners on the Sea of Japan coast will likely want a post-winter round to catch lightning damage before spring maintenance.

Cadence matters for AI too. Every consistent annual round makes the model's comparisons more useful, because it has a clean before image to compare against.

What does an AI-assisted inspection look like in the field?

Here's a pattern I've seen many times, described generically.

An onshore turbine is flown after typhoon season. The model returns a few dozen flags across 3 blades. Most are contamination: rain streaks and droppings on the suction side. The reviewer clears them quickly.

One flag sits on the trailing edge at about two thirds of span. It's a thin dark line, low confidence, labelled as a stain.

The inspector zooms in, then opens the matching frame from the opposite face. The line continues across the edge. That's a trailing edge split, and it moves from cosmetic to a grade that needs a repair date.

The model did its part. It put the line on the list. A human who knew to check the other face made the call that mattered. If the confidence threshold had been set a little higher, that crack would have stayed in the folder until next year.

Why train inspectors on a simulator before they fly?

Because the grading skill above is learned from repetition, and the real blade is an expensive place to make your first mistakes.

I built a browser-based Turbine Inspection Simulator for exactly this. Crews use it to rehearse the professional blade defect detection workflow before anyone climbs or flies: the flight order around the 4 faces, standoff distance, image overlap, spotting each defect class, and grading what they find.

It runs in a browser, so there's no drone, no weather window and no vessel day involved. A trainee can miss a hairline crack, see why, and try again in the same session.

It's also how I demo the workflow to buyers. A wind farm owner or a drone service company can see what the inspector sees and what the final report looks like before signing anything. The simulator is part of Wind Hub on fabien-starseed.com, alongside the weather view CTV captains use for go or no-go calls.

For drone service companies preparing for Japan's market, this matters twice. You'll be proving your process to new clients who haven't seen your field work. Showing them a trained, repeatable grading workflow is stronger evidence than a slide.

What should buyers in Taiwan and Japan demand in an AI inspection report?

A report that separates what the model found from what a human graded, and lets you check both.

Ask for these, at minimum:

  • Location for every defect. Turbine, blade ID, face, and radius in metres from the root.
  • Size and orientation. Length, width, spanwise or chordwise.
  • Severity grade with the grader named. Model suggestion and human decision, side by side.
  • Confidence scores and rejected flags. You should see what the AI flagged and the inspector dismissed.
  • Comparison with the last inspection. Same blade, same face, same radius, with growth noted.
  • Full image access. You own the raw photos and the data, not just a PDF.
  • Language your team works in. Chinese for a Taiwan asset team, Japanese where the owner needs it, English for international stakeholders.

The data ownership point gets skipped too often. If your inspection images live only in a vendor's platform, next year's comparison depends on that vendor. Keep the originals, keep the metadata, and keep the grading history in a format you can move.

Where this leaves drone service companies

The crews that will win work in Taiwan and Japan over the next few years will be the ones whose reports hold up when an owner's engineer challenges a grade.

AI gets you to the shortlist faster. Training, consistent cadence and an honest report get you the next contract.

I'm working toward my Japanese drone licence (Class 2) and preparing for that market now, with my own well-maintained equipment, licences in several countries, and a registered, fully insured company in Taiwan. If you run a drone service company or manage blades in Taiwan or Japan and want to see the simulator or talk through your reporting pipeline, get in touch through fabien-starseed.com.

快速解答: 風機無人機檢測 AI 會掃描無人機在每座風機拍下的數百張照片,標出疑似缺陷,例如前緣侵蝕、後緣裂縫和雷擊損傷。它找出候選缺陷的速度很快,但 1 到 5 級的嚴重度分級,仍需要受過訓練的檢測員確認位置、尺寸和擴展情況。

台灣風機葉片檢測 AI:模型會出錯的地方

風機無人機檢測 AI 非常擅長找出葉片上的每一個痕跡。它不擅長的是判斷其中哪些痕跡會讓你賠上一支葉片,而這第二個判斷,才是資產業主真正付錢買的東西。

我在台灣檢測過約 3,000 座陸域和離岸風機。看過這麼多葉片之後,我的立場是:讓模型負責找,讓受過訓練的檢測員負責分級,並讓報告標明每個判定是由誰做出的。

AI 在無人機葉片檢測中到底做什麼?

它負責整理影像。無人機繞一座風機飛一趟,會拍下數百張高解析度照片,涵蓋每支葉片的 4 個面,AI 再把這一大堆照片整理成一份疑似缺陷的候選清單。

這 4 個面是前緣、後緣、壓力面和吸力面。3 支葉片,就是每座風機 12 個拍攝航段。在有 AI 之前,審查人員得手動一張張捲動檢視。現在模型會框出異常、建議缺陷類別,並附上信心分數。

這確實省下不少時間。問題在於哪些東西會進到候選清單。

用通用資料集訓練的模型,會把鳥糞、輪轂流下的油污痕跡、雨珠、塔架陰影和前緣累積的蟲屍都標記出來。在台灣海峽的離岸場址,鏡頭上的鹽霧還會造成額外的誤報。每一個誤報都要花人幾秒鐘處理。整座風場累積下來,這些秒數會變成好幾天。

反方向的錯誤更糟。一道對比度低的細裂縫被判為污漬,信心分數低於門檻,就永遠到不了人的眼前。

檢測員在嚴重度分級表旁,檢視 AI 標記的葉片後緣裂縫影像

在台灣和日本,哪些葉片缺陷最重要?

前緣侵蝕、後緣裂縫、雷擊損傷,以及失效的前緣保護層。哪一項排在第一,取決於氣候。

在台灣,主要因素是季風雨、颱風和鹽分。大型離岸轉子的葉尖速度接近 90 m/s,每一滴雨打在前緣上都像砂礫。侵蝕從塗層的點蝕開始,一路往下侵入積層。

日本則多了另一種壓力。日本海沿岸冬季雷擊的能量異常強大,這點已有充分記錄,而這段海岸包括秋田。日本正朝 2040 年離岸風電 30 到 45 GW 的目標推進,秋田是最早的離岸風電區域之一。在那裡,葉尖附近和接閃器周圍的雷擊損傷值得特別留意。

以下是 AI 在各類缺陷上的表現,依據是我拿模型輸出和自己的分級比對時看到的結果:

缺陷類別AI 擅長的部分AI 的弱點檢測員要確認什麼
前緣侵蝕能穩定找出點蝕和塗層剝落無法從單張影像判斷深度積層或纖維是否外露
後緣裂縫能找出長而張開的裂口髮絲裂縫會被誤認為髒污或黏合線長度、方向,以及後緣兩側
雷擊損傷能找出接閃器上的燒痕分辨煙灰與焦痕,以及葉尖附近隱藏的脫層接閃器狀況、葉尖鼓起、是否需要後續追蹤
前緣保護層脫膠能找出翹起的保護膠帶或護殼邊緣尚未產生陰影的早期翹起保護區的邊緣、剝離方向
表面污染每次都找得到把它標成損傷將它從缺陷清單中移除
附加件(渦流產生器、鋸齒尾緣)能清點缺少的零件仍在原位但底座已裂開的零件對照葉片圖面清點數量

這個規律很一致。缺陷對比強、形狀清楚時,AI 表現很好。當答案取決於深度、脈絡或葉片的另一面時,它就力不從心。

葉片缺陷嚴重度怎麼分級?為什麼模型無法獨自完成?

大多數報告採用 1 到 5 級的嚴重度量表,從外觀問題到必須停機。分級需要位置、尺寸和歷史紀錄,而單張照片只能提供其中一部分。

不同風機製造商和業主的量表各有差異,但常見的架構大致如下:

  1. 外觀。 記錄即可,不需處理。
  2. 輕微。 下次檢測時持續觀察。
  3. 中度。 在下一個計畫性維護窗口修復。
  4. 嚴重。 盡快修復,考慮降載運轉。
  5. 危急。 停機。

以一道 10 cm 的裂縫為例。如果它在葉根附近、沿弦向延伸,可能是結構性問題。如果它在葉尖附近、沿展向延伸,而且只在塗層,可能只是 2 級。兩種情況下,模型看到的都是一樣的像素。

裂縫沿葉片的位置(以距葉根的公尺數計算)會改變分級。方向也會。裂縫是否跨越後緣黏合線也會。

再來是歷史紀錄。擴展是葉片檢測中最強的訊號。一個長度比去年增加一倍的 2 級缺陷,已經不再是 2 級。除非 AI 流程能把去年的影像對應到同一支葉片、同一面、同一半徑位置,否則它根本看不到擴展。

風機葉片多久應該做一次無人機檢測?

每年一次建立基準,再加上在任何可能讓葉片狀況一夜改變的事件之後,進行針對性飛行。

觸發條件為什麼重要常見範圍
年度基準檢測建立歷史紀錄,讓擴展看得見所有葉片、全部 4 個面
颱風過後突發裂縫、脫膠、附加件脫落先針對性檢查,再全面檢測
雷擊警報後接閃器燒痕、葉尖損傷遭雷擊的那座風機
保固到期前作為求償證據全面、高解析度、完整記錄
修復後確認修補有效修復區域

在台灣,我會把年度檢測安排在颱風季以外,並讓團隊隨時準備好颱風後的飛行。在日本,日本海沿岸的業主很可能會希望在冬季過後安排一輪檢測,在春季維護前抓出雷擊損傷。

檢測頻率對 AI 也很重要。每一輪一致的年度檢測,都會讓模型的比對更有用,因為它有一張乾淨的「之前」影像可以對照。

AI 輔助檢測在現場是什麼樣子?

以下是我看過很多次的情況,以一般化的方式描述。

一座陸域風機在颱風季後進行飛行檢測。模型在 3 支葉片上回報了幾十個標記。大部分是污染:吸力面上的雨痕和鳥糞。審查人員很快就把它們排除。

有一個標記位於後緣、大約三分之二展長處。那是一條細細的暗線,信心分數低,被標成污漬。

檢測員放大檢視,接著打開對面那一面的對應影像。那條線延伸跨過了後緣。這是後緣開裂,等級從外觀問題升為需要排定修復日期的級別。

模型完成了它的部分,把這條線列進了清單。真正關鍵的判定,是由一位知道要檢查另一面的人做出的。如果信心門檻再設高一點,這道裂縫就會在資料夾裡一直待到明年。

為什麼要讓檢測員先在模擬器上訓練再飛?

因為上面講的分級技能是靠反覆練習學來的,而在真正的葉片上犯第一個錯誤,代價很高。

我正是為此打造了一套在瀏覽器執行的 Turbine Inspection Simulator(風機檢測模擬器)。團隊在任何人攀爬或起飛之前,先用它演練專業的葉片缺陷檢測流程:繞 4 個面的飛行順序、安全距離、影像重疊率、辨識每一類缺陷,以及為發現的缺陷分級。

它在瀏覽器裡執行,所以不需要無人機、不需要等天氣窗口,也不需要出船。學員可能漏掉一道髮絲裂縫,看到原因,然後在同一次練習中再試一次。

這也是我向買方展示流程的方式。風場業主或無人機服務公司在簽約前,就能看到檢測員看到的畫面,以及最終報告的樣子。這套模擬器是 fabien-starseed.com 上 Wind Hub 的一部分,旁邊還有 CTV 船長用來判斷是否出航的天氣畫面。

對準備進入日本市場的無人機服務公司來說,這點更加重要。你要向還沒看過你現場作業的新客戶證明你的流程。展示一套經過訓練、可重複的分級流程,比一張簡報投影片更有說服力。

台灣和日本的買方應該要求 AI 檢測報告包含什麼?

一份把模型找到的東西和人員分級的結果分開呈現,並讓你兩者都能查核的報告。

至少要求以下幾項:

  • 每個缺陷的位置。 風機、葉片編號、哪一面,以及距葉根的半徑(公尺)。
  • 尺寸與方向。 長度、寬度、展向或弦向。
  • 嚴重度分級並註明分級者。 模型建議與人員判定並列呈現。
  • 信心分數與被排除的標記。 你應該看得到 AI 標記了哪些,檢測員又排除了哪些。
  • 與上次檢測的比較。 同一支葉片、同一面、同一半徑位置,並註明擴展情況。
  • 完整影像存取權。 原始照片和資料歸你所有,而不只是一份 PDF。
  • 團隊使用的語言。 台灣資產團隊用中文,業主需要時用日文,國際利害關係人用英文。

資料所有權這一點太常被忽略。如果你的檢測影像只存在某家廠商的平台上,明年的比對就得仰賴那家廠商。保留原始檔、保留中繼資料,並以可轉移的格式保存分級紀錄。

這對無人機服務公司意味著什麼

未來幾年能在台灣和日本拿到案子的團隊,會是那些報告經得起業主工程師質疑分級的團隊。

AI 讓你更快拿到候選清單。訓練、穩定的檢測頻率和誠實的報告,才能讓你拿到下一份合約。

我正在考取日本無人機證照(二等),現在就在為那個市場做準備,擁有維護良好的自有設備、多國證照,以及一家在台灣登記、保險齊全的公司。如果你經營無人機服務公司,或在台灣或日本管理風機葉片,想看看模擬器或聊聊你的報告流程,歡迎透過 fabien-starseed.com 與我聯繫。

Quick answer: 風車のドローン点検AIは、ドローンが1基あたり数百枚撮影する写真をスキャンし、前縁エロージョン、後縁クラック、落雷損傷といった欠陥の候補を抽出します。候補を見つけるのは速いものの、1〜5段階の重大度判定には、位置、サイズ、進行状況を確認できる訓練を受けた検査員が今も欠かせません。

台湾のブレード点検AI:モデルが見誤るポイント

風車のドローン点検AIは、ブレード上のあらゆる痕跡を見つけることには非常に長けています。一方で、その中のどれがブレード1枚分のコストにつながるかを判断するのは苦手です。そして、アセットオーナーが対価を払っているのは、まさにその2つ目の判断です。

私はこれまで台湾で、陸上と洋上を合わせて約3,000基の風車を点検してきました。数多くのブレードを見てきた私の考えはこうです。発見はモデルに任せ、判定は訓練を受けた検査員が行い、報告書にはそれぞれの判定をどちらが下したかを明示することです。

ドローンによるブレード点検で、AIは実際に何をしているのか?

AIがしているのは画像の仕分けです。風車1基の周囲を1回飛行すると、各ブレードの4面をカバーする高解像度写真が数百枚得られます。AIはその膨大な写真を、欠陥の疑いがある箇所の候補リストにまとめます。

4面とは、前縁、後縁、圧力面、負圧面のことです。ブレードは3枚なので、1基あたり12パスになります。AI以前は、レビュー担当者が全フレームを手作業でスクロールして確認していました。今ではモデルが異常箇所を枠で囲み、欠陥の分類を提案し、信頼度スコアを付けてくれます。

これで実際に何時間も節約できます。問題は、候補リストに何が載るかです。

汎用データセットで学習したモデルは、鳥の糞、ハブから垂れたグリースの筋、雨粒、タワーの影、前縁に付着した虫の堆積物まで検出してしまいます。台湾海峡の洋上では、レンズに付く塩分のもやが、さらに独自の誤検出を生みます。誤検出1件ごとに、人間の作業時間が数秒ずつ奪われます。ウィンドファーム全体で見れば、その数秒が数日分に膨らみます。

逆方向のエラーはさらに深刻です。コントラストの低い細いクラックが汚れと判定されて信頼度のしきい値を下回り、一度も人間の目に触れないまま終わってしまうのです。

AIが検出した後縁クラックのブレード画像を重大度判定シートと並べて確認する検査員

台湾と日本で特に重要なブレード欠陥は?

前縁エロージョン、後縁クラック、落雷損傷、そして劣化した前縁保護材です。どれが最優先になるかは気候によって決まります。

台湾での主な要因は、モンスーンの雨、台風、塩分です。大型の洋上ローターは翼端速度が約90 m/sに達するため、雨粒の一つひとつが砂粒のように前縁を打ちつけます。エロージョンはコーティングの点食から始まり、やがて積層材まで進行します。

日本では、これとは別のストレスが加わります。日本海沿岸の冬季雷はエネルギーが異常に大きいことがよく知られています。この沿岸には、2040年までに洋上風力30〜45 GWを目指す日本の取り組みのなかで、最初に洋上風力が進んだ地域の一つである秋田も含まれます。そうした地域では、翼端付近やレセプター周辺の落雷損傷に特に注意を払う必要があります。

以下は、モデルの出力を私自身の判定と照らし合わせてレビューした経験に基づく、欠陥分類ごとのAIの性能です。

欠陥分類AIが得意なことAIが苦手なこと検査員が確認すること
前縁エロージョン点食やコーティングの剥離を確実に発見する1枚の画像から深さを判断できない積層材や繊維が露出しているか
後縁クラック長く開いた割れを発見するヘアラインクラックを汚れや接着ラインと誤認する長さ、向き、エッジの両面
落雷損傷レセプターの焼け跡を発見するすすと焦げの区別、翼端付近の隠れた層間剥離レセプターの状態、翼端の膨らみ、追加調査の要否
前縁保護材の剥離浮き上がったテープやシェルの端を発見する影ができない初期段階の浮き保護範囲の端、剥がれの方向
表面の汚れ毎回確実に発見する損傷として分類してしまう欠陥リストから除外する
付属品(ボルテックスジェネレーター、セレーション)欠落数をカウントする取り付いたままの基部のひび割れブレード図面と照合して数を確認する

傾向は一貫しています。AIは、コントラストが強く形のはっきりした欠陥には強い一方、深さや前後関係、ブレードの反対面の情報が判断に必要な場合には苦戦します。

ブレード欠陥の重大度はどう判定するのか?なぜモデルだけでは判定できないのか?

多くの報告書では、外観上の問題から運転停止までを表す1〜5段階の重大度スケールが使われています。判定には位置、サイズ、履歴が必要ですが、1枚の写真にはその一部しか写っていません。

スケールは風車メーカーやオーナーによって異なりますが、一般的な形は次のとおりです。

  1. 外観上の問題。 記録のみ、対応不要。
  2. 軽微。 次回の点検で経過観察。
  3. 中程度。 次の計画メンテナンスの機会に補修。
  4. 重大。 早期に補修し、運転の抑制を検討。
  5. 危機的。 風車を停止。

長さ10 cmのクラックを例に取りましょう。翼根付近で翼弦方向に走っていれば、構造上の懸念になり得ます。翼端付近で翼幅方向に走り、コーティングだけにとどまっていれば、判定は2程度かもしれません。どちらの場合も、モデルには同じピクセルしか見えていません。

翼根から何メートルの位置にあるかで、判定は変わります。向きによっても変わります。後縁の接着ラインをまたいでいるかどうかによっても変わります。

さらに履歴の問題があります。ブレード点検において、進行は最も強いシグナルです。前年から長さが倍になった2は、もはや2ではありません。AIパイプラインが前年の画像を同じブレード、同じ面、同じ半径位置で照合していない限り、進行はまったく見えません。

風車ブレードのドローン点検はどのくらいの頻度で行うべきか?

ベースラインとして年1回、それに加えて、ブレードの状態が一晩で変わり得る事象のあとに的を絞った飛行を行います。

きっかけ重要な理由一般的な範囲
年次ベースライン進行を把握するための履歴を蓄積する全ブレード、4面すべて
台風通過後突発的なクラック、剥離、付属品の脱落まず対象を絞り、その後全体
落雷アラーム後レセプターの焼損、翼端の損傷被雷した風車
保証期間終了前保証請求の根拠となる証拠全体、高解像度、記録付き
補修後補修が持ちこたえているかを確認補修箇所

台湾であれば、年次点検は台風シーズンを避けて計画し、嵐のあとの飛行に備えてクルーを待機させておくのがよいでしょう。日本では、日本海沿岸のオーナーは、春のメンテナンス前に落雷損傷を把握するため、冬明けの点検を求めることが多いと思われます。

点検の頻度はAIにとっても重要です。毎年一貫した条件で点検を重ねるほど、比較対象となるきれいな過去画像が揃い、モデルによる比較がより役立つものになります。

現場でのAI支援点検はどのように進むのか?

ここでは、私が何度も目にしてきたパターンを一般化して紹介します。

台風シーズン後に、ある陸上風車を飛行点検します。モデルは3枚のブレード全体で数十件の検出結果を返します。そのほとんどは汚れで、負圧面の雨の筋や鳥の糞です。レビュー担当者はそれらを素早く除外します。

検出結果の一つが、翼幅の約3分の2の位置の後縁にあります。細く暗い線で、信頼度は低く、汚れとラベル付けされています。

検査員は画像を拡大し、反対面の対応するフレームを開きます。線はエッジをまたいで続いています。これは後縁の割れであり、判定は外観上の問題から、補修日の設定が必要なレベルへと引き上げられます。

モデルは自分の役割を果たしました。その線を候補リストに載せたのです。そして、反対面を確認すべきだと知っていた人間が、本当に重要な判断を下しました。もし信頼度のしきい値がもう少し高く設定されていたら、このクラックは翌年までフォルダの中に埋もれたままだったでしょう。

なぜ飛行前にシミュレーターで検査員を訓練するのか?

上で述べた判定スキルは反復によって身につくものであり、実機のブレードは最初の失敗をするには高くつく場所だからです。

私はまさにこの目的のために、ブラウザで動くTurbine Inspection Simulatorを開発しました。クルーは誰かが登ったり飛ばしたりする前に、このシミュレーターでプロのブレード欠陥検出ワークフローを練習します。4面を回る飛行順序、離隔距離、画像のオーバーラップ、各欠陥分類の見分け方、見つけた欠陥の判定までを一通り行えます。

ブラウザで動くため、ドローンも天候の合間も船の手配も必要ありません。訓練生はヘアラインクラックを見落としても、その理由を確認し、同じセッションの中でもう一度挑戦できます。

購入を検討している方へのワークフローのデモにも使っています。ウィンドファームのオーナーやドローンサービス会社は、契約前に、検査員が何を見ているのか、最終報告書がどのようなものになるのかを確認できます。このシミュレーターはfabien-starseed.comのWind Hubの一部で、CTV船長が出航可否の判断に使う気象ビューと並んで提供しています。

日本市場への参入を準備しているドローンサービス会社にとって、これは二重の意味で重要です。皆さんは、現場での実績を見たことがない新しい顧客に対して、自社のプロセスを証明していくことになります。訓練された再現性のある判定ワークフローを見せることは、スライド資料よりも強い証拠になります。

台湾と日本の発注者は、AI点検報告書に何を求めるべきか?

モデルが見つけたものと人間が判定したものを分けて示し、その両方を検証できる報告書です。

最低限、次の項目を求めてください。

  • すべての欠陥の位置。 風車、ブレードID、面、翼根からの半径位置(メートル)。
  • サイズと向き。 長さ、幅、翼幅方向か翼弦方向か。
  • 判定者名を記した重大度判定。 モデルの提案と人間の判断を並べて記載。
  • 信頼度スコアと却下された検出結果。 AIが検出し、検査員が除外したものも確認できるべきです。
  • 前回点検との比較。 同じブレード、同じ面、同じ半径位置での比較と、進行状況の記載。
  • 全画像へのアクセス。 PDFだけでなく、元の写真とデータの所有権も発注者にあります。
  • チームが使う言語での記載。 台湾のアセットチームには中国語、オーナーが必要とする場合は日本語、海外の関係者には英語。

データの所有権は見落とされがちです。点検画像がベンダーのプラットフォーム上にしかなければ、翌年の比較はそのベンダー次第になってしまいます。元画像とメタデータを手元に残し、判定履歴も移行可能な形式で保管しておきましょう。

ドローンサービス会社にとっての意味

今後数年、台湾と日本で仕事を勝ち取るのは、オーナー側のエンジニアから判定について問われても、報告書の内容がそれに耐えられるクルーでしょう。

AIを使えば、候補リストにより早くたどり着けます。次の契約につながるのは、訓練、一貫した点検頻度、そして誠実な報告書です。

私は現在、日本の二等無人航空機操縦士の取得を目指しながら、日本市場への準備を進めています。手入れの行き届いた自前の機材、複数の国でのライセンス、そして台湾に登記し十分な保険に加入した会社を持っています。台湾または日本でドローンサービス会社を運営している方、あるいはブレードを管理している方で、シミュレーターをご覧になりたい場合や報告書作成の流れについて相談されたい場合は、fabien-starseed.comからお気軽にご連絡ください。

Frequently asked questions常見問題よくある質問

Can AI replace a human inspector in wind turbine blade inspection?Can AI replace a human inspector in wind turbine blade inspection?Can AI replace a human inspector in wind turbine blade inspection?
No. AI is fast at finding anomalies in drone images, but severity grading depends on defect location, orientation, depth and growth since the last inspection. A trained inspector still needs to confirm each flag and assign the grade.No. AI is fast at finding anomalies in drone images, but severity grading depends on defect location, orientation, depth and growth since the last inspection. A trained inspector still needs to confirm each flag and assign the grade.No. AI is fast at finding anomalies in drone images, but severity grading depends on defect location, orientation, depth and growth since the last inspection. A trained inspector still needs to confirm each flag and assign the grade.
How many photos does a drone take to inspect one wind turbine?How many photos does a drone take to inspect one wind turbine?How many photos does a drone take to inspect one wind turbine?
Usually several hundred high-resolution images. The drone covers 4 faces on each of the 3 blades (leading edge, trailing edge, pressure side and suction side), which makes 12 passes per turbine.Usually several hundred high-resolution images. The drone covers 4 faces on each of the 3 blades (leading edge, trailing edge, pressure side and suction side), which makes 12 passes per turbine.Usually several hundred high-resolution images. The drone covers 4 faces on each of the 3 blades (leading edge, trailing edge, pressure side and suction side), which makes 12 passes per turbine.
What blade defects does AI miss most often?What blade defects does AI miss most often?What blade defects does AI miss most often?
Hairline trailing edge cracks with low contrast, which models often label as stains or bond lines, plus early leading edge protection debonding and hidden delamination near lightning-struck tips. These need a human check, often against the opposite face of the blade.Hairline trailing edge cracks with low contrast, which models often label as stains or bond lines, plus early leading edge protection debonding and hidden delamination near lightning-struck tips. These need a human check, often against the opposite face of the blade.Hairline trailing edge cracks with low contrast, which models often label as stains or bond lines, plus early leading edge protection debonding and hidden delamination near lightning-struck tips. These need a human check, often against the opposite face of the blade.
How often should offshore wind blades in Taiwan be inspected?How often should offshore wind blades in Taiwan be inspected?How often should offshore wind blades in Taiwan be inspected?
Plan an annual baseline inspection of all blades and all faces, then add targeted drone flights after typhoons, lightning alarms and repairs. A pre-warranty-end inspection is also worth doing for evidence.Plan an annual baseline inspection of all blades and all faces, then add targeted drone flights after typhoons, lightning alarms and repairs. A pre-warranty-end inspection is also worth doing for evidence.Plan an annual baseline inspection of all blades and all faces, then add targeted drone flights after typhoons, lightning alarms and repairs. A pre-warranty-end inspection is also worth doing for evidence.
Who should own the data from a drone blade inspection?Who should own the data from a drone blade inspection?Who should own the data from a drone blade inspection?
The asset owner. Ask for full access to the raw images, metadata and grading history in a portable format, so next year's growth comparison doesn't depend on a single vendor's platform.The asset owner. Ask for full access to the raw images, metadata and grading history in a portable format, so next year's growth comparison doesn't depend on a single vendor's platform.The asset owner. Ask for full access to the raw images, metadata and grading history in a portable format, so next year's growth comparison doesn't depend on a single vendor's platform.